Request Estimate

 

 

Presented here below you'll find additional decent news involving How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Setting up a tub isn't specifically rocket science, however it does need solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably hard project. If the old tub is easily accessible, the project can move immediately; if you need to open up a wall to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as embeded in the brand-new one. See to it you have actually certified yourself for the job and are comfortable attempting it. Instead of hiring a professional to take over a halfway-completed job, it is much better to think about utilizing one prior to you start. Possibilities are you might require an expert plumber to make tube links.
This post will assist you set up a new tub in your restroom if you have already purchased a new tub as well as don't need to alter the arrangement of your previous supply of water pipes.
Your tools and also product list must make up the following:

 

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Measuring tape


• Pipe Caps


 

Preparing for the Installation

Firstly, the sustaining framework supplied with the bath needs to be fitted (if called for) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to make sure that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps unit to stop pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be fitted in its last setting.

 

 

Removing Old Touches

If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you ought to do is separate the supply of water. After doing so, switch on the taps to drain pipes any water staying in the system. The process of getting rid of the existing taps can be rather bothersome because of the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.

 

 

Mounting the Bathtub

Utilizing both wood boards under its feet, put the bath tub in the called for position. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bathtub until the spirit level checks out level.
To set up faucets, fit all-time low of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Turn on the supply of water and inspect all joints as well as new pipework for leaks as well as tighten them if required. Fill up the tub and likewise inspect the overflow outlet as well as the typical outlet for leaks.
Finally, repair the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub should wait till the bathtub has been used at least when as this will certainly resolve it right into its final position.

 

 

Fitting New Taps

If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Protect the tap in place with the supplier supplied backnut. Once the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be attached to the faucet ends initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bathtub

In the location where the bath fulfills the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, causing difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Bear in mind to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or waterproof sticky and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you really like reading about How to Install a Bathtub Yourself? Write feedback down the page. We'd be interested to know your feelings about this post. We hope that you come back again in the future. I beg you take the opportunity to distribute this article if you enjoyed it. I am grateful for your time. Don't hesitate to come by our site back soon.

Request Estimate